Categories
Belkin Router

How To Setup Belkin Router | Install Belkin Wireless Router |

Are you looking information about Belkin router setup?

If you are doing so, let me inform you, you are at right place to get help.

This article will help you in installing the Belkin wireless router. You need to read this article until the end and follow the instructions to fix the problem.

belkin router setup, install belkin router

The requirement for Belkin router setup –

There is no big requirement for installing a belkin wireless router. You just need a few things,

  • Internet Connection.
  • Ethernet Cable.
  • Computer or smartphone.

Install belkin router-

To set up a wireless router, first, you need to make a physical connection between the Belkin router, modem, and computer.

So you need to unbox the belkin wireless router from the box and follow the instructions given below.

  1. Power off your Internet Modem.
  2. Take an ethernet cable and connect your modem from internet port of the belkin router.
  3. Now take another ethernet cable, and connect your computer from any empty LAN port of the wireless router.

Note: if you are using a laptop or smartphone, you may try to connect to your belkin router using WiFi facility.

  1. Plug in the power cable into your wireless router and turn on the internet modem as well, wait for one minute. So the orange light can turn into solid blue or green light.

If you are getting blinking orange light on your router, you need to check the connection between belkin router and internet modem.

For brief information you may visit: how to fix belkin router blinking orange problem.

Setup Belkin Router using web-based dashboard–

Once you will install the belkin wireless router and start getting a blue or green light. it’s time to setup belkin router via dashboard or setup page and follows the instructions given below,

Note-  these instructions are for belkin smart wifi routers only. if you have a simple wireless router.

you may ignore these steps because your router is already set up.

So you may go ahead and start connecting your devices.

  • Open the web browser into your computer and type the belkin router’s ip address in the top address bar, by default it is: 192.168.2.1
  • Now you will able to see let’s connect to the internet page, here you need to click on detect my connection and wait for a second.
  • Once your belkin router will detect the wireless connection, it will display the default username and password for the wifi network.

you may change this username or password any time, if you wish to do it right now, then you need to change it

  • After changing the username and password, you will able to see the confirmation window, here you need to click on Great what’s next!.
  • Now you will able to see the registration page, you need to fill the details if you want to register the page. else, you can click on register later.
  • Finally, you will able to see the confirmation window, so you need to click on take me to the dashboard.

Hopefully, your belkin router will be set up. you may go ahead and try to connect your wireless router to the internet.

Follow Us On Facebook: https://www.facebook.com/fixotip

Categories
Belkin Router

5 Quick Ways To Fix Belkin Router Blinking Orange Or Solid Amber Light

Why is my Belkin router blinking orange problem –

When you get Belkin router blinking orange light problem, there can be several reasons behind this problem.

Today, in this article I will point out the way to fix the Belkin router flashing orange or blinking yellow light problem.

If you are also experiencing the same problem with your Belkin wireless router.

I will suggest you read this post until the end and follow the steps to fix the issue.

  • Connection Problem
  • Router setup problem.
  • Internet Connection Problem
  • Firmware Update Problem.

How To Fix Belkin router flashing orange light problem-

Now we know the reason behind Belkin router is blinking orange.

So it’s a time to troubleshoot the problem.

But before fixing the problem, you should try to power cycle the devices once and wait for a second.

  1. Power off your internet modem, wait for 10 seconds and plug power if back on.
  2. Now unplug the power cable from the Belkin router and wait for 10 seconds, now plug it back in.
  3. After turning on your modem and router, you need to wait for 1 minute.

let’s see if you can get blue light or yellow light on your Belkin router.

1. Check Physical Connection-

Did you check the cable connection between a Belkin router and internet modem?

Because, if your router is not connected to the modem properly.

that’s you might get the flashing orange or yellow internet light on your wireless router.

also few times, you might get blinking orange light due to a faulty ethernet cable.

So I will ask you to replace the ethernet cable, and reboot the wireless router.

Now check which color of light, you can see on your Belkin router?

If you can see the blue light on your router, that’s great.. you are good to go.

but sadly, if you are still getting blinking orange light on your Belkin router.

Do not worry; we are still here with other steps to fix the router.

2. Update the firmware-

if you are using old firmware on your wireless router.

It may not allow you to access the internet and give you blinking orange internet light in revert.

belkin router blinking orange, belkin router flashing orange,

That’s why having updated firmware is very important. So you should check for the router firmware update.

if you will find any update. I will suggest you, update it instantly.

3. Clone the mac address-

When your modem is not able to identify the device, it will stop serving the internet.

as a result, you will have a blinking orange light on your Belkin wireless router.

belkin router blinking orange, belkin router flashing orange

To do the mac cloning you need to follow the steps given below.

  • Connect your laptop to the router via ethernet cable.
  • Now open the Belkin router setup page.
  • Go to mac cloning.
  • Click on clone my mac address.
  • Finally, you need to click on apply changes.

Now your router will save the settings and restart itself for once.

Once your router will be power up, you will get solid green or blue light on it.

4. IP Conflict Issue- 

did you check the ip address of your router and modem?

make sure they both do not belong to the same class.

belkin router blinking orange, belkin router flashing orange, belkin router not working

in any case, if they do?

you have to change the ip address of your router and choose the ip address, which belongs to some other class.

also, do not forget to change the subnet mask as well.

5. Factory Restore the wireless router-

After performing the above steps, if your Belkin router is still blinking orange.

I will suggest you, factory restore the wireless router.

So you need to press the hold the reset button on your Belkin router for one minute and then release it.

one you will release the button, you need to restart the router and setup Belkin Wireless Router again.

Now I hope your router will start working If still, your Belkin router is not working.

then your router is the hardware failure,

in that case, you have to replace your wireless router.

Thank you for reading this post.

Categories
Belkin Router

How To Setup Belkin Range Extender Without Cd ?

Easy Way To setup Belkin Range Extender :

Most people don’t know what is range extender also how to set up Belkin range extender. Router signals become weak after a particular area. So the router is not sufficient for covering the big wireless area. Wireless extender uses for connecting all the devices with internet in big offices and homes.

The wireless range extender is a device, which is used for increasing the signal strength of the wireless network. We can connect all the devices in a big area of the network with the help of many extenders.

setup belkin range extender

In other words, you can say, “wireless range extender works like a booster”.  It increases the wireless signal strength of your router. In this article, I am going to explain, how to set up Belkin range extender?

Requirement For set up Belkin Range Extender-

Below are the instructions for how to set up Belkin range extender. First, I would love to talk about what is the requirement for installing the range extender.

  1. Wireless Network – As we have already told you about how does range extender work. So if you are going to set up a range extender. You must have a wireless network.
  2. Computer or Smartphone– When you will try to install range extender. You need a computer or smartphone. Through which you can configure your extender.

How To install Belkin range extender-

  • Un-box the range extender and plug in the power adapter.
  • Take an Ethernet cable and connect your Belkin range extender to the computer.

Note– If you have a laptop or wireless computer, you may try to connect to your range extender using wifi method.

you will able to see default wireless name, Belkin Ext in your available wireless network list.

  • Open the Web browser, like – google chrome, safari, internet explorer etc also type range extenders IP address in the top address bar.
  • Now you will able to see Belkin range extender welcome page, simply press setup range extender.
  • When you will able to see available wireless networks, choose your wireless network from the list and press next.
  • Here this will ask you for your Passphrase, you need to type your passphrase and press next.
  • Now your Belkin range extender will verify the login credential. if the information will successfully be verified. you will see the confirmation window.
  • In this window, you need to simply click on setup extender, and click on next.

Finally, your range extender will be set up, you may place your range extender, where you are getting the low signal.

If you have any other question also the suggestion, leave a comment below. So we can make Fixotip better and our team will reply solution.

Thank you for reading the post.

Categories
Belkin

How To Fix Belkin Range Extender Is Blinking Orange

When your Belkin range extender is blinking orange or flashing amber light, there can be several reasons for this problem.

Today, I am writing the troubleshooting steps for Belkin range extender blinking orange problem. If someone from you is going through the same problem.

read this article until the end and follow the instructions to fix the problem.

Note– Before troubleshooting your range extender makes sure you are getting internet on your modem or router, so connect your computer directly to your router or modem and try to access the internet.

Somehow if you are unable to access the internet, then you need to contact your internet service provider and ask them for help.

Basic Troubleshooting Steps:

  1. Power off the Belkin range extender for 10 seconds and then power it back on and wait for 1 minute. Let’s see, if your Belkin range extender is still blinking orange.
  2. Make sure your wireless router is on and it is working perfectly fine. Maybe your wireless router is turned off or not functioning that’s why you might be getting amber light on your Belkin range extender.
  3. Place your Belkin range extender nearby your router and plug it into the power. Now wait for 1 minute and let’s see if it is giving you green light or your belkin extender is still blinking orange.

If you have a solid orange or yellow light on your belkin range extender, then it is just a problem with the wifi range, so you have to install your range extender within the wifi range.

Advance Troubleshooting steps for Belkin range extender is blinking orange –

talking about my personal experience, whenever I find Belkin range extender not working problem. I always check the ip address of the device. because it can tell you the root cause of the problem.

If you are getting a range extenders to default IP address, then this problem may be related to connectivity.

So you have to connect your Belkin range extender to the router once again.

But if you are getting ip from APIPA (169.X.X.X), then this problem can be related to hardware or firmware.

In that situation, you need to you need to reset the belkin range extender and setup it again.

  1. Press and hold the reset button on your range extender using a paper clip or pin for 30 seconds.
  2. Now power off your range extender for one minute and then power it back on.
  3. Once your belkin range extender will be powered on, you need to connect your computer to the extender using Ethernet cable or wifi function.

After connecting your range extender to the computer, its time to setup belkin range extender once again. so go ahead and setup it.

After following the above steps, I hope you will get rid of Belkin range extender is blinking orange problem.

if you have any other problem, please leave a comment below, we will reply it with the solution.

Thank you for reading this post.